You can either send us your vehicle or chassis by mail for processing, or you can oder it directly from us.You can choose from the following options:Disassembly only
(You send in your vehicle or purchase one from us)Chassis cut‑outs only
(You send in your chassis)Chassis cut‑outs and installation of the drive units
(You send in your chassis)Vehicle disassembly and chassis cut‑outs
(You send in your vehicle or purchase one from us)Vehicle disassembly, chassis cut‑outs, and installation of the drive unit
(You send in your vehicle or purchase one from us)Feel free to contact us anytime.
Dual rear axle for 6×6 Mercedes Sprinter 2021 by BruderThe set includes all components required to equip a Bruder® 6×6 Mercedes Sprinter with two rigid rear axles and single‑wheel drive.
The newly developed powered rigid rear axles by 3D‑Parts for the Sprinter allow lateral articulation and independent suspension on both sides. The wheels no longer tilt as they did with previous versions.
The plastic components are sintered from polyamide using rapid prototyping.
Some cuts to the vehicle frame of the Bruder Sprinter are necessary for installation. Experience in model building is required for this conversion.With the rims offered here, the distance from outer tire edge to outer tire edge is 134 mm.
The width without axle stubs is 112 mm.The motors with 150 rpm are designed for operation at 12 volts.
The motors with 300 rpm are designed for 7.4‑volt LiPos.All screws, nuts, axles and coil springs are included.
You will still need:4 motors: 6 V 300 rpm or 12 V 150 rpmNote: Tires and rims are not included in the set.
No electronics or cables are supplied.Video instructions for opening the Sprinter and installing our axles can be found here.
The set includes all components needed to convert the new 2021 Mercedes Sprinter models by Bruder® to front-wheel drive with individual wheel drive.
The plastic components are made of polyamide using rapid prototyping sintering. Some cuts to the vehicle frame of the Bruder Sprinter are necessary for installation. Experience in model building is required for this conversion. With the rims offered here, the distance from the outer edge of one tire to the outer edge of the other tire is 134mm. The width without axle stubs is 112mm.
The set includes all screws, ball joints, threaded rods, nuts, axles, and coil springs.
You will also need:
2 motors: 6V 300rpm or 12V 150rpm
Servo
Note: Tires and rims are not included in the set. Additionally, no electronics or cables are provided."
Newly developed sets for illuminating the original headlight lenses of the Bruder Sprinter model.
Please purchase the required 1206 SMD LEDs with pre‑soldered enamel wires, for example from: www.leds-and-more.de
You can also obtain the resistors there.The set includes:1 pair of black inserts, left and rightCircuit diagram with resistor values for 5 V (BEC) operating voltageIf you order with LEDs and resistors, we additionally supply:2 white (or warm‑white) SMD LEDs, size 1206, with pre‑soldered enamel wires2 orange SMD LEDs, size 1206, with pre‑soldered enamel wires2 × 150‑ohm resistors, e.g. these1 × 47‑ohm resistor, e.g. this oneIMPORTANT: This set fits only the new (2021) Sprinter model by Bruder.
Installation kit for rear light with indicatorNewly developed sets for illuminating the original rear light lenses of the Bruder Sprinter model.
Please purchase the required 1206 SMD LEDs with pre‑soldered enamel wires, for example from: www.leds-and-more.de
You can also obtain the resistors there.Please note: Since the lens is red, the indicator will appear more red even though an orange LED is used.The set includes:1 pair of black inserts, left and rightCircuit diagram with resistor values for 5 V (BEC) operating voltageIf you order with LEDs and resistors, we additionally supply:4 red SMD LEDs, size 1206, with pre‑soldered enamel wires2 orange SMD LEDs, size 1206, with pre‑soldered enamel wires2 × 150‑ohm resistors, e.g. these1 × 33‑ohm resistor, e.g. this oneIMPORTANT: This set fits only the new (2021) Sprinter model by Bruder.
MB Sprinter 2021 ambulance with installed drive systemWe have disassembled the vehicle, carried out all necessary cuts and drillings, and installed our drive axles.
To complete the vehicle, you will still need:Rims and tiresSpeed controllerBattery and cablesReceiverAnd if you order without motors and servo:2 motors: 6 V 300 rpm or 12 V 150 rpmServoPlease note a delivery time of up to 6 weeks for the modified vehicle.
We have disassembled the vehicle and made all the necessary cuts and drillings to install our drive axles. To complete the vehicle, you will need:
Rims and road tires or off-road tires
Speed controller
Battery and cables
Motors: 6V 300rpm or 12V 150rpm
Servo
Please note the delivery time of up to 6 weeks for the modified vehicle.
We have disassembled the vehicle and made all the necessary cuts and drillings to install our drive axles. To complete the vehicle, you will need:
Rims and road tires or off-road tires
Speed controller
Battery and cables
Motors: 6V 300rpm or 12V 150rpm
Servo
Please note the delivery time of up to 6 weeks for the modified vehicle.
MB Sprinter 2021 DHL with Installed Drive UnitWe have disassembled the vehicle, carried out all necessary cuts and drillings, and installed our drive axles. To complete the vehicle, you will still need:Rims and tiresSpeed controllerBattery and cablesReceiverAnd if you order without motors and servo:2 motors: 6 V 300 rpm or 12 V 150 rpmServoPlease note the delivery time of up to 6 weeks for the modified vehicle.
MB Sprinter 2021 Municipal version – opened and pre‑preparedWe have disassembled the vehicle and completed all necessary cuts and drillings so that you can install our drive axles.
To complete the vehicle, you will additionally need:Rims and tiresElectronic speed controllerBattery and cablesReceiverAnd if you order without motors and servo:2 motors: 6 V 300 rpm or 12 V 150 rpmServoPlease note a delivery time of up to 6 weeks for the modified vehicle.
MB Sprinter 2021 Municipal Version with Installed Drive UnitWe have disassembled the vehicle, carried out all necessary cuts and drillings, and installed our drive axles. To complete the vehicle, you will still need:Rims and tiresSpeed controllerBattery and cablesReceiverAnd if you order without motors and servo:2 motors: 6 V 300 rpm or 12 V 150 rpmServoPlease note the delivery time of up to 6 weeks for the modified vehicle.
MB Sprinter 2021 Transfer with installed drive systemWe have disassembled the vehicle, completed all necessary cuts and drillings, and installed our drive axles.
To complete the vehicle, you will additionally need:Rims and tiresElectronic speed controllerBattery and cablesReceiverIf you order without motors and servo:2 motors: 6 V 300 rpm or 12 V 150 rpmServoPlease note a delivery time of up to 6 weeks for the modified vehicle.
The set includes all components needed to equip a Mercedes Sprinter by Bruder® with a rigid rear axle and individual wheel drive.
The new powered rigid rear axles from 3D-Parts for the RAM and Sprinter allow lateral tilting and independent suspension on both sides. Unlike previous models, the wheels remain aligned properly.
The plastic components are made of polyamide using rapid prototyping sintering. Some cuts to the vehicle frame of the Bruder Sprinter are necessary for installation. Experience in model building is required for this conversion. With the rims offered here, the distance from the outer edge of one tire to the outer edge of the other tire is 134mm. The width without axle stubs is 112mm.
The motors with 150 revolutions per minute are designed for operation with 12 volts. Motors with 300 revolutions per minute are suitable for 7.4-volt LiPo batteries. The set includes all screws, nuts, axles, and coil springs.
You will also need:
2 motors: 6V 300rpm or 12V 150rpm
Note: Tires and rims are not included in the set. Additionally, no electronics or cables are provided.
€44.00*
This website uses cookies to ensure the best experience possible. More information...
